Diy Wifi Antenna Booster What Material to Use

Download Article

Download Commodity

Have you lost your WiFi antenna? Most antennas can be removed from WiFi cards, making them like shooting fish in a barrel to lose. With a few household supplies, you can make an effective replacement antenna that tin get y'all by until you can purchase a replacement. If you are having range issues, you tin create your own directional antenna that tin can significantly increase the distance of your wireless connection.

1. i

   Assemble your materials and tools. In order to brand the antenna, you volition demand a big paper clip (fifty-75 mm, or two-3 inches long), an empty Bic ballpoint pen, and a gyre of electrical record. Yous volition also need a metric ruler, scissors, wire cutters, and a lighter.

2. 2

   Straighten the paper clip. Unfold the newspaper clip into straight slice of metal.

   Advertisement

3. 3

   Measure and cut the newspaper prune. In club to get the all-time point, your paper prune wire should be 61 mm long (2.4 inches). Endeavour to get as close to this measurement as possible for the most constructive antenna.

4. 4

   Bend the newspaper clip. Bend about xix mm (three/4 inch) of one end of the straightened wire at a ninety° angle. This volition be the part that inserts into the WiFi antenna port.

5. 5

   Remove the ink cartridge from the pen. Since you're going to be clipping the ink cartridge, it'southward best if you use a pen that is empty and doesn't write anymore. Clip off about 12-18 mm (1/2 - three/iv inch) of the tubing that used to contain the ink. If it is not empty, this can get messy, so be sure to concur the tube abroad from yous when yous cut. Cut the tube over a surface that y'all don't mind getting stained.

6. 6

   Sideslip the tubing over the bent role of the paper clip. Place the cut-off piece of tubing over the bent end of the paper clip. Make sure that the tubing extends past the terminate of the newspaper clip past about 1.5 mm (one/xvi inch).

7. seven

   Shrink the tubing with the lighter. Have a lighter or other heat source and GENTLY estrus the tubing on the paper clip. This volition shrink the tubing and make a tight fit to the newspaper clip.

8. 8

   Insulate the antenna. Wrap the newspaper prune in electrical tape to prevent excess interference with the wireless signal.

9. 9

   Insert the paper prune into the antenna port. Insert the 'tubing' end of the paper prune into the antenna connector, ensuring that the connector pin and the paper clip are pressed together within the tubing. If you can get them to overlap the signal volition exist even ameliorate.

   Advertisement

1. ane

   Collect your materials and tools. To build this directional antenna, you volition need an N-Female person chassis mount connector, four #6x1/4" basics and bolts, 1-1/4" (32 mm) copper wire, pigtail patch cable, and an empty aluminum tin.

   • You volition besides need a drill, a soldering iron, and a screwdriver that fits the bolts
   • A pigtail cable is a patch cablevision with a connector at both ends of the cable.
   • The aluminum can should have one side without a chapeau and ane side with a metal bottom.

2. 2

   Measure the tin's diameter. The can's diameter determines where the connector is mounted. Your tin can should exist at least 3 inches (7.6 cm) wide, but tin can be as big as 6 inches (15.ii cm).

3. 3

   Marking the connector's mounting indicate. Measure upwards from the bottom of the can and marking the exterior where the connector volition exist. The measurement will vary depending on the diameter of the can. This measurement is determined for maximum point forcefulness. Below are some common measurements:

   • 3 inches (7.half-dozen cm) - 3.74 inches (ix.5 cm)
   • 3.5 inches (viii.9 cm) - 2.07 inches (5.25 cm)
   • half dozen inches (15.two cm) - 1.38 inches (iii.five cm)

4. 4

   Punch a hole in the side of the tin. Use a drill bit the aforementioned size as the small side of the N-Female connector to drill a hole where you lot measure. Y'all tin also use a hammer and nail if you don't have a drill.

   • If your N-Female connector has screw holes, drill smaller holes effectually your larger ane to permit you to mount it with the nuts and bolts.

5. 5

   Mensurate and cutting the wire. Take your copper wire and line information technology upward with the the metal connector on the small side of the N-Female connector. The little brass tube and the length of the wire should total i.21 inches (iii.07 cm) when lined upward. Get as shut to this measurement every bit physically possible for the all-time connection.

6. half-dozen

   Solder the copper wire to the small stop of the Northward-Female person connector. Use the soldering iron to attach the wire to the brass tube on the back of the N-Female connector. This creates the probe. Run into this guide for details on soldering. The wire should be sticking direct out from the connector.

7. 7

   Secure the probe in the tin. After the solder has finished cooling, mount the probe to the can with the wire on the within and the screw connector on the outside. Use the nuts and bolts to secure the probe to the can.

8. 8

   Connect the can to the wireless card using the pigtail cable. Spiral the pigtail cablevision onto the probe mount, and and so connect the other stop to your wireless menu's antenna connector.

9. 9

   Bespeak the can at the physical access bespeak. The can volition need to be pointed direct at the wireless access point. You can mount it to a camera tripod with a aught tie for easy pointing.^[i]

   • The range y'all tin can reach with your antenna will vary depending on the size of the can, the accuracy of your measurements, and whatsoever interference between the antenna and the admission point.

   Advertisement

Add New Question

• Question

  How do I pick upwardly Wi-Fi from a weak source?

  

  Movement your device closer to the Wi-Fi source or reconfigure your settings/router.

Enquire a Question

200 characters left

Include your e-mail address to become a message when this question is answered.

Submit

Advertisement

Cheers for submitting a tip for review!

About This Article

Article Summary X

To brand a WiFi antenna using a paper clip, start by straightening out the paper clip and cut information technology so information technology's 61 millimeters long. So, almost 19 millimeters away from ane of the ends, bend the paper clip at a ninety-degree angle. Side by side, take the ink cartridge out of a ballpoint pen, and cut off 12-18 millimeters of the tubing that contains ink. Once you've done that, slide the cut-off piece of tubing over the bent role of the paper prune, and gently heat information technology with a lighter to brand the tubing shrink. Finally, insulate the antenna with electrical record before inserting information technology into the antenna port. To larn how to make a directional antenna, ringlet down!

Did this summary help you?

Thanks to all authors for creating a folio that has been read 247,426 times.

Is this article up to engagement?

melbourneamigh1952.blogspot.com

Source: https://www.wikihow.com/Make-a-Wifi-Antenna

Share this post